ElmLod attributesPowerFactory General Load

Every attribute of the PowerFactory General Load (ElmLod): 199 input parameters and 1129 result variables, with units and meaning. Copy a name into GetAttribute or SetAttribute.

What ElmLod is

A general load. Its P and Q are set on the element; how they change with voltage and frequency is set in the load type (TypLod).

Class: ElmLod, element class
PowerFactory name: General Load
Type: TypLod, through typ_id
Terminal suffix: :bus1 terminal
Attributes: 199 input parameters and 1129 result variables, in 7 calculations

Most used ElmLod attributes

Attribute	Unit	Description	Where
`m:P:bus1`	MW	Active Power	Load flow
`m:Q:bus1`	Mvar	Reactive Power	Load flow
`m:I:bus1`	kA	Current, Magnitude	Load flow
`plini`	MW	Active Poweractive power demand	input data
`qlini`	Mvar	Reactive Powerreactive power demand	input data
`scale0`	·	Scaling Factorscaling factor	input data
`slini`	MVA	Apparent Power	input data
`coslini`	·	Power Factor	input data
`outserv`	·	Out of Service	input data
`typ_id`	·	Type	input data

Read and write ElmLod in Python

import powerfactory

app = powerfactory.GetApplication()          # GetApplicationExt() from outside PowerFactory
app.GetFromStudyCase("ComLdf").Execute()      # results exist after a calculation

for load in app.GetCalcRelevantObjects("*.ElmLod"):
    p_bus1 = load.GetAttribute("m:P:bus1")        # Active Power, MW
    q_bus1 = load.GetAttribute("m:Q:bus1")        # Reactive Power, Mvar
    print(load.loc_name, p_bus1, q_bus1)

load = app.GetCalcRelevantObjects("*.ElmLod")[0]
load.SetAttribute("plini", 140)               # demand 140 MW

A result at a terminal of the general load needs the terminal in its name: m:P:bus1, not m:P, which raises AttributeError.
An input parameter is read and written with or without its e: prefix: GetAttribute("outserv") and GetAttribute("e:outserv") give the same value.
RMS and EMT variables change over time: record them in a results object (ElmRes) to read the whole curve. GetAttribute after a run gives the value at the last time step.

Input parameters199
Load flow results230
Short-circuit results286
RMS simulation results250
EMT simulation results135
DC load flow results29
Modal analysis results80
Optimal power flow results119
Basic data1

ElmLod input parameters

The element data, as typed in GetAttribute and SetAttribute (the e: prefix is optional). Setting one changes the model.

Attribute	Unit	Description
`loc_name`	·	Name
`chr_name`	·	Characteristic Name
`for_name`	·	Foreign Key
`dat_src`	·	Data source
`mode_inp`	·	Input Mode
`sernum`	·	Serial Number
`commissionDate`	·	Commissioning Date
`appr_modby`	·	Modified by
`classif`	·	Load Classification
`outserv`	·	Out of Service
`i_sym`	·	Balanced/Unbalanced
`constr`	·	Year of Construction
`appr_status`	·	Status
`icurref`	·	Harmonic currents referred to
`OptCost`	·	Unit
`NrCust`	·	Number of connected customers
`i_prty`	·	Priority
`shed`	·	Shedding steps
`i_scale`	·	Adjusted by Load Scaling
`i_pini`	·	Estimate Active Power
`i_qini`	·	Estimate Reactive Power
`i_scaleini`	·	Estimate Scaling Factor
`i_rem`	·	Remote Control
`iShedding`	·	Allow load shedding
`isCtrlLdShed`	·	Allow load shedding
`ctrlUsage`	·	Load shedding
`iecfltcont`	·	Fault Contribution
`iecShcModel`	·	Short-Circuit Model
`iLoadTrf`	·	Consider Load Transformer
`i_normPQext`	·	Pext, Qext input signals normalised to load flow voltage
`LTC`	·	LTC flag , LTC
`iAstabint`	·	A-stable integration algorithm
`plini`	MW	Active Power
`qlini`	Mvar	Reactive Power
`plinir`	MW	Active Power
`qlinir`	Mvar	Reactive Power
`plinis`	MW	Active Power
`qlinis`	Mvar	Reactive Power
`plinit`	MW	Active Power
`qlinit`	Mvar	Reactive Power
`scale0`	·	Scaling Factor
`u0qvref`	p.u.	Reference voltage
`Q0qvref`	Mvar	Q reference
`pcontract`	MW	Contracted Active Power
`u0`	p.u.	Voltage
`fSCDF`	·	Scaling factor
`trans`	%	Transferable
`shedcost`	USD/MVAh	Costs for load shedding
`shedmax`	%	Max. load shedding
`shedmin`	%	Min. load shedding
`Skss`	MVA/MW	Subtransient Short-Circuit Level
`Sks`	MVA/MW	Transient Short-Circuit Level
`rtox`	·	R to X'' ratio
`Skssfix`	MVA	Subtransient Short-Circuit Level
`Sksfix`	MVA	Transient Short-Circuit Level
`Skssfixmin`	MVA	Subtransient Short-Circuit Level
`Sksfixmin`	MVA	Transient Short-Circuit Level
`rtoxmin`	·	R to X'' ratio
`Strat`	MVA	Rated Power
`r0`	p.u.	r0
`x0`	p.u.	x0
`xt`	%	Load Transformer Reactance
`Bc_hv`	Mvar	HV Capacitance
`Bc_lv`	Mvar	Additional LV Capacitance
`Vmin`	p.u.	LTC Vmin, Vmin
`Vmax`	p.u.	LTC Vmax, Vmax
`Bss`	p.u.	Shunt capacitor at LV bus, Bss
`Rfdr`	p.u.	Feeder R, Rfdr
`Xfdr`	p.u.	Feeder X, Xfdr
`Fb`	·	Fraction of feeder Q-comp., Fb
`Fma`	·	Motor A fraction
`Fmb`	·	Motor B fraction
`Fmc`	·	Motor C fraction
`Fmd`	·	Motor D fraction
`Fel`	·	Electronic load fraction
`GPSlat`	deg	Latitude / Northing
`GPSlon`	deg	Longitude / Easting
`curativeLim`	%	Max. curative power deviation
`curativeCosts`	USD/MVAh	Costs for curative power deviation
`dudropLVfeed`	%	Maximum Voltage Drop (LV Grid)
`duriseLVfeed`	%	Maximum Voltage Rise (LV Grid)
`dpl1`	·	dpl1
`dpl2`	·	dpl2
`dpl3`	·	dpl3
`dpl4`	·	dpl4
`dpl5`	·	dpl5
`appr_modif`	·	Modified
`cimRdfId`	·	RDF ID
`desc`	·	Description
`fold_id`	·	In Folder
`typ_id`	·	TypeObject: TypLod,TypLodind,TypLodwecc
`bus1`	·	TerminalObject: StaCubic
`pQPcurve`	·	Q(P)-CurveObject: IntQpcurve
`pQVcurve`	·	Q(V)-CurveObject: IntQvcurve
`doc_id`	·	Additional Data
`pOwner`	·	OwnerObject: ElmOwner
`pOperator`	·	OperatorObject: ElmOperator
`phmc`	·	Harmonic CurrentsObject: TypHmccur,TypHmcopcur
`pSCDF`	·	TariffObject: IntTariffenergy,IntTarifftime,ChaVec
`pTrans`	·	Alternative Supply (Load)Object: ElmLod,ElmLodlv,ElmLodmv
`p_cub`	·	Controlled Branch (Cubicle)Object: StaCubic*
`cpHeadFold`	·	Head Folder
`bus1_bar`	·	Terminal
`cpGrid`	·	GridObject: ElmNet
`cpZone`	·	ZoneObject: ElmZone
`cpArea`	·	AreaObject: ElmArea
`cpFeed`	·	FeederObject: ElmFeeder
`ciDist`	·	Distance from infeed in number of buses
`ciLater`	·	Lateral Index
`ciDistRoot`	·	Distance from first infeed in number of buses
`ciDistAll`	·	Distance from infeed in number of buses including switches
`ciDistAllRoot`	·	Distance from first infeed in number of buses including switches
`cpOwner`	·	OwnerObject: ElmOwner
`cpOperator`	·	OperatorObject: ElmOperator
`cpBranch`	·	BranchObject: ElmBranch
`cpSite`	·	SiteObject: ElmSite
`cpSubstat`	·	SubstationObject: ElmSubstat,ElmTrfstat
`cpMeteostat`	·	Meteo StationObject: ElmMeteostat
`ciOutaged`	·	Planned Outage
`ciEnergized`	·	Energized
`ciEarthed`	·	Earthed
`cDisplayName`	·	Display Name
`cpSupplyTransformer`	·	Supplying TransformerObject: ElmTr?,ElmTrmult
`cpSupplyTrfStation`	·	Supplying Secondary SubstationObject: ElmTrfstat
`cpSupplySubstation`	·	Supplying SubstationObject: ElmSubstat
`slini`	MVA	Apparent Power
`coslini`	·	Power Factor
`ilini`	kA	Current
`pf_recap`	·	Power Factor
`p_direc`	·	Power Direction
`slinir`	MVA	Apparent Power
`coslinir`	·	Power Factor
`ilinir`	kA	Current
`pf_recapr`	·	Power Factor
`p_direcr`	·	Power Direction
`slinis`	MVA	Apparent Power
`coslinis`	·	Power Factor
`ilinis`	kA	Current
`pf_recaps`	·	Power Factor
`p_direcs`	·	Power Direction
`slinit`	MVA	Apparent Power
`coslinit`	·	Power Factor
`ilinit`	kA	Current
`pf_recapt`	·	Power Factor
`p_direct`	·	Power Direction
`av_mode`	·	Local Controller
`q0qvref`	p.u.	Q reference
`phtech`	·	Technology
`Inom`	kA	Nominal Current
`cTypHmc`	·	Type of harmonic sources
`Irated`	kA	Rated Current
`cTrans`	%	Resulting
`cEstPhases`	·	Estimate phases
`plini_a`	MW	P(act.)
`qlini_a`	Mvar	Q(act.)
`slini_a`	MVA	S(act.)
`coslini_a`	·	cos(phi)(act.)
`ilini_a`	kA	I(act.)
`scale0_a`	·	Scaling Factor(act.)
`zonefact`	·	Zone Scaling Factor
`qdslCtrl`	·	Quasi-Dynamic ModelObject: ElmQdsl
`plinir_a`	MW	Ph 1
`qlinir_a`	Mvar	Ph 1
`slinir_a`	MVA	Ph 1
`coslinir_a`	·	Ph 1
`ilinir_a`	kA	Ph 1
`plinis_a`	MW	Ph 2
`qlinis_a`	Mvar	Ph 2
`slinis_a`	MVA	Ph 2
`coslinis_a`	·	Ph 2
`ilinis_a`	kA	Ph 2
`plinit_a`	MW	Ph 3
`qlinit_a`	Mvar	Ph 3
`slinit_a`	MVA	Ph 3
`coslinit_a`	·	Ph 3
`ilinit_a`	kA	Ph 3
`Ikss`	kA/MW	Subtransient Short-Circuit Current
`Iks`	kA/MW	Transient Short-Circuit Current
`xtor`	·	X'' to R ratio
`Ikssfix`	kA	Subtransient Short-Circuit Level
`Iksfix`	kA	Transient Short-Circuit Level
`Ikssfixmin`	kA	Subtransient Short-Circuit Level
`Iksfixmin`	kA	Transient Short-Circuit Level
`xtormin`	·	X'' to R ratio
`cBasedOn`	MVA	based on
`ctotSkss`	MVA	Total contribution (subtransient)
`ctotSks`	MVA	Total contribution (transient)
`ctotIkss`	kA	Total contribution (subtransient)
`ctotIks`	kA	Total contribution (transient)
`ctotSkssmin`	MVA	Total contribution (subtransient)
`ctotSksmin`	MVA	Total contribution (transient)
`ctotIkssmin`	kA	Total contribution (subtransient)
`ctotIksmin`	kA	Total contribution (transient)
`r2Sbasepu`	p.u.	r2(shc) (Sbase)
`x2Sbasepu`	p.u.	x2(shc) (Sbase)
`r1Sbasepu`	p.u.	r1(shc) (Sbase)
`x1ssSbasepu`	p.u.	x1''(shc) (Sbase)
`x1sSbasepu`	p.u.	x1'(shc) (Sbase)
`ramp_type`	·	Allow Load-Ramp Event

ElmLod load flow results

Read after ComLdf with GetAttribute. m: currents, voltages and powers, c: calculation parameter, n: bus result at a terminal, s: signal (state or model variable).

Attribute	Unit	Description
`m:urnet:bus1`	p.u.	Voltage, Real Part, referred to network
`m:uinet:bus1`	p.u.	Voltage, Imaginary Part, referred to network
`m:u1r:bus1`	p.u.	Positive-Sequence-Voltage, Real Part
`m:u1i:bus1`	p.u.	Positive-Sequence-Voltage, Imaginary Part
`m:u1:bus1`	p.u.	Positive-Sequence-Voltage, Magnitude
`m:U1:bus1`	kV	Line-Ground Positive-Sequence-Voltage, Magnitude
`m:U1l:bus1`	kV	Line-Line Positive-Sequence-Voltage, Magnitude
`m:phiu1:bus1`	deg	Positive-Sequence-Voltage, Angle
`m:irnet:bus1`	p.u.	Current, Real Part, referred to network
`m:iinet:bus1`	p.u.	Current, Imaginary Part, referred to network
`m:inet:bus1`	p.u.	Current, Magnitude, referred to network
`m:I:bus1`	kA	Current, Magnitude
`m:phii:bus1`	deg	Current, Angle
`m:i1r:bus1`	p.u.	Positive-Sequence Current, Real Part
`m:i1i:bus1`	p.u.	Positive-Sequence Current, Imaginary Part
`m:i1:bus1`	p.u.	Positive-Sequence Current, Magnitude
`m:I1:bus1`	kA	Positive-Sequence Current, Magnitude
`m:phii1:bus1`	deg	Positive-Sequence Current, Angle
`m:P:bus1`	MW	Active Power
`m:Q:bus1`	Mvar	Reactive Power
`m:S:bus1`	MVA	Apparent Power
`m:cosphi:bus1`	·	Power Factor
`m:tanphi:bus1`	·	tan(phi)
`m:Psum:bus1`	MW	Total Active Power
`m:Qsum:bus1`	Mvar	Total Reactive Power
`m:Ssum:bus1`	MVA	Total Apparent Power
`m:cosphisum:bus1`	·	Total Power Factor
`m:tanphisum:bus1`	·	Total tan(phi)
`m:i1P:bus1`	p.u.	Positive-Sequence Active Current
`m:i1Q:bus1`	p.u.	Positive-Sequence Reactive Current
`m:I1P:bus1`	kA	Positive-Sequence Active Current
`m:I1Q:bus1`	kA	Positive-Sequence Reactive Current
`m:ur:bus1`	p.u.	Voltage, Real Part
`m:ui:bus1`	p.u.	Voltage, Imaginary Part
`m:u:bus1`	p.u.	Voltage, Magnitude
`m:ir:bus1`	p.u.	Current, Real Part
`m:ii:bus1`	p.u.	Current, Imaginary Part
`m:i:bus1`	p.u.	Current, Magnitude
`m:phiui:bus1`	deg	Angle between Voltage and Current
`m:phiu1i1:bus1`	deg	Angle between Voltage and Current in positive sequence system
`m:Tfct:bus1`	s	Fault Clearing Time
`m:Brkload:bus1`	%	Breaker Loading
`m:Spu:bus1`	MVA/p.u.	Apparent Power per p.u. Voltage
`m:urnet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Real Part, referred to network
`m:uinet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Imaginary Part, referred to network
`m:u0:bus1`	p.u.	Zero-Sequence-Voltage, Magnitude
`m:phiu0:bus1`	deg	Zero-Sequence-Voltage, Angle
`m:u2:bus1`	p.u.	Negative-Sequence-Voltage, Magnitude
`m:phiu2:bus1`	deg	Negative-Sequence-Voltage, Angle
`m:irnet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Real Part, referred to network
`m:iinet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Imaginary Part, referred to network
`m:inet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Magnitude, referred to network
`m:I:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Phase Current, Magnitude
`m:phii:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Phase Current, Angle
`m:i0r:bus1`	p.u.	Zero-Sequence Current, Real Part
`m:i0i:bus1`	p.u.	Zero-Sequence Current, Imaginary Part
`m:i0:bus1`	p.u.	Zero-Sequence Current, Magnitude
`m:I0:bus1`	kA	Zero-Sequence Current, Magnitude
`m:I0x3:bus1`	kA	3*I0
`m:phii0:bus1`	deg	Zero-Sequence Current, Angle
`m:i2r:bus1`	p.u.	Negative-Sequence Current, Real Part
`m:i2i:bus1`	p.u.	Negative-Sequence Current, Imaginary Part
`m:i2:bus1`	p.u.	Negative-Sequence Current, Magnitude
`m:I2:bus1`	kA	Negative-Sequence Current, Magnitude
`m:phii2:bus1`	deg	Negative-Sequence Current, Angle
`m:ubfacI:bus1`	%	Current Unbalance Factor
`m:ubfacS:bus1`	%	Power Unbalance Factor
`m:P:bus1:A`per phase :A, :B, :C, unbalanced only	MW	Active Power
`m:Q:bus1:A`per phase :A, :B, :C, unbalanced only	Mvar	Reactive Power
`m:S:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	Apparent Power
`m:cosphi:bus1:A`per phase :A, :B, :C, unbalanced only	·	Power Factor
`m:tanphi:bus1:A`per phase :A, :B, :C, unbalanced only	·	tan(phi)
`m:Pln:bus1:A`per phase :A, :B, :C, unbalanced only	MW	Active Power (Line-Neutral)
`m:Qln:bus1:A`per phase :A, :B, :C, unbalanced only	Mvar	Reactive Power (Line-Neutral)
`m:P1:bus1`	MW	Positive Sequence Active Power
`m:Q1:bus1`	Mvar	Positive Sequence Reactive Power
`m:P2:bus1`	MW	Negative Sequence Active Power
`m:Q2:bus1`	Mvar	Negative Sequence Reactive Power
`m:P0:bus1`	MW	Zero Sequence Active Power
`m:Q0:bus1`	Mvar	Zero Sequence Reactive Power
`m:i2P:bus1`	p.u.	Negative-Sequence Active Current
`m:i2Q:bus1`	p.u.	Negative-Sequence Reactive Current
`m:I2P:bus1`	kA	Negative-Sequence Active Current
`m:I2Q:bus1`	kA	Negative-Sequence Reactive Current
`m:ur:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Real Part
`m:ui:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Imaginary Part
`m:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Magnitude
`m:ir:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Real Part
`m:ii:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Imaginary Part
`m:i:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Magnitude
`m:phiui:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle between Voltage and Current
`m:phiu0i0:bus1`	deg	Angle between Voltage and Current in zero-sequence system
`m:phiu2i2:bus1`	deg	Angle between Voltage and Current in negative sequence system
`m:TfctPh:bus1:A`per phase :A, :B, :C, unbalanced only	s	Fault Clearing Time
`m:BrkloadPh:bus1:A`per phase :A, :B, :C, unbalanced only	%	Breaker Loading
`c:frnom`	Hz	Nominal Frequency
`c:hpi`	rad/s	Nominal angular frequency
`c:pini`	MW	Nominal Active Power
`c:scale0`	·	Initial Scale Factor
`c:s`	·	Complex Power (P+jQ)
`c:u0`	p.u.	Nominal Voltage
`c:kpu0`	·	Volt. Dependence I on P
`c:kqu0`	·	Volt. Dependence I on Q
`c:kpu1`	·	Volt. Dependence II on P
`c:kqu1`	·	Volt. Dependence II on Q
`c:kpu`	·	Volt. Dependence III on P
`c:kqu`	·	Volt. Dependence III on Q
`c:aP`	·	Percent of Volt. Dep. I on P
`c:bP`	·	Percent of Volt. Dep. II on P
`c:aQ`	·	Percent of Volt. Dep. I on Q
`c:bQ`	·	Percent of Volt. Dep. II on Q
`c:Qnom`	Mvar	Nominal Reactive Power
`c:ncust`	·	Number of Connected Customers
`c:i_rem`	·	Remote Control
`c:zonescale`	·	Zone Scale Factor
`c:iRefElement`	·	Reference Element
`c:Pmism`	MW	Active Power Mismatch
`c:Ploss`	MW	Losses (total)
`c:Qloss`	Mvar	Reactive-Losses (total)
`c:Plossld`	MW	Losses (load)
`c:Qlossld`	Mvar	Reactive-Losses (load)
`c:Plossnld`	MW	Losses (no load)
`c:Qlossnld`	Mvar	Reactive-Losses (no load)
`c:qini`	Mvar	Nominal Reactive Power
`c:Pnom`	MW	Nominal Active Power
`c:Ppeak`	MW	Peak Active Power
`c:Qpeak`	Mvar	Peak Reactive Power
`c:p`	MW	Power
`c:gs0`	p.u.	Conductance
`c:bs0`	p.u.	Susceptance
`c:x`	p.u.	Reactance
`c:r`	p.u.	Resistance
`c:slip`	p.u.	Slip
`c:sr`	MVA	Complex Power (P+jQ), ph. A
`c:ss`	MVA	Complex Power (P+jQ), ph. B
`c:st`	MVA	Complex Power (P+jQ), ph. C
`c:z0`	p.u.	z0
`c:prini`	MW	Nominal Active Power, ph. A
`c:qrini`	Mvar	Nominal Reactive Power, ph. A
`c:psini`	MW	Nominal Active Power, ph. B
`c:qsini`	Mvar	Nominal Reactive Power, ph. B
`c:ptini`	MW	Nominal Active Power, ph. C
`c:qtini`	Mvar	Nominal Reactive Power, ph. C
`c:cnm`	·	Connection
`n:ur:bus1`	p.u.	Voltage, Real Part
`n:ui:bus1`	p.u.	Voltage, Imaginary Part
`n:u:bus1`	p.u.	Voltage, Magnitude
`n:upc:bus1`	%	Voltage, Magnitude
`n:du:bus1`	%	Voltage Deviation
`n:U:bus1`	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1`	deg	Voltage, Angle
`n:phiurel:bus1`	deg	Voltage, Relative Angle
`n:Ul:bus1`	kV	Line-Line Voltage, Magnitude
`n:u1:bus1`	p.u.	Voltage, Magnitude
`n:u1pc:bus1`	%	Voltage, Magnitude
`n:u1r:bus1`	p.u.	Positive-Sequence Voltage, Real Part
`n:u1i:bus1`	p.u.	Positive-Sequence Voltage, Imaginary Part
`n:Pgen:bus1`	MW	Generation, Active Power
`n:Qgen:bus1`	Mvar	Generation, Reactive Power
`n:Pmot:bus1`	MW	Motor Load, Active Power
`n:Qmot:bus1`	Mvar	Motor Load, Reactive Power
`n:Pload:bus1`	MW	General Load, Active Power
`n:Qload:bus1`	Mvar	General Load, Reactive Power
`n:Pcomp:bus1`	MW	Compensation (Losses)
`n:Qcomp:bus1`	Mvar	Compensation
`n:Pnet:bus1`	MW	External Networks, Active Power
`n:Qnet:bus1`	Mvar	External Networks, Reactive Power
`n:Pflow:bus1`	MW	Power Flow, Active Power
`n:Qflow:bus1`	Mvar	Power Flow, Reactive Power
`n:Pout:bus1`	MW	Outgoing Flow, Active Power
`n:Qout:bus1`	Mvar	Outgoing Power, Reactive Power
`n:Sout:bus1`	MVA	Outgoing Power, Apparent Power
`n:cosphiout:bus1`	·	Outgoing Power, Power Factor
`n:Pbalance:bus1`	MW	Active Power Balance (=0)
`n:Qbalance:bus1`	Mvar	Reactive Power Balance (=0)
`n:LossPdown:bus1`	MW	Losses, downstream
`n:LossQdown:bus1`	Mvar	Losses, downstream (Reactive Power)
`n:LossPdownload:bus1`	MW	Load losses, downstream
`n:LossQdownload:bus1`	Mvar	Load losses, downstream
`n:LossPdownnoload:bus1`	MW	No load losses, downstream
`n:LossQdownnoload:bus1`	Mvar	No load losses, downstream
`n:du_feed:bus1`	%	Difference from voltage at start of feeder
`n:ur:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Real Part
`n:ui:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Imaginary Part
`n:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Magnitude
`n:upc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Ground Voltage, Magnitude
`n:du:bus1:A`per phase :A, :B, :C, unbalanced only	%	Voltage Deviation
`n:U:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Ground Voltage, Angle
`n:ul:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Line Voltage, Magnitude
`n:ulpc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Line Voltage, Magnitude
`n:Ul:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Line Voltage, Magnitude
`n:phiul:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Line Voltage, Angle
`n:u0:bus1`	p.u.	Zero-Sequence Voltage, Magnitude
`n:U0:bus1`	kV	Zero-Sequence Voltage, Magnitude
`n:U0x3:bus1`	kV	3*U0
`n:phiu0:bus1`	deg	Zero-Sequence Voltage, Angle
`n:U1:bus1`	kV	Line-Ground Positive-Sequence Voltage, Magnitude
`n:phiu1:bus1`	deg	Positive-Sequence Voltage, Angle
`n:u2:bus1`	p.u.	Negative-Sequence Voltage, Magnitude
`n:U2:bus1`	kV	Line-Ground Negative-Sequence Voltage, Magnitude
`n:phiu2:bus1`	deg	Negative-Sequence Voltage, Angle
`n:U1l:bus1`	kV	Line-Line Positive-Sequence Voltage, Magnitude
`n:U2l:bus1`	kV	Line-Line Negative-Sequence Voltage, Magnitude
`n:uln:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Neutral Voltage, Magnitude
`n:Uln:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Neutral Voltage, Magnitude
`n:phiuln:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Neutral Voltage, Angle
`n:un:bus1`	p.u.	Neutral-Ground Voltage, Magnitude
`n:Un:bus1`	kV	Neutral-Ground Voltage, Magnitude
`n:phiun:bus1`	deg	Neutral-Ground Voltage, Angle
`n:upht:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Technology dependent Voltage, Magnitude
`n:Upht:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Phase Technology dependent Voltage, Magnitude
`n:um:bus1`	p.u.	Average-Voltage, Magnitude
`n:Um:bus1`	kV	Average-Voltage, Magnitude
`n:uphtmin:bus1`	p.u.	Minimum of Phase Technology dependent Voltage, Magnitude
`n:uphtmax:bus1`	p.u.	Maximum of Phase Technology dependent Voltage, Magnitude
`n:ubfac:bus1`	%	Unbalance Factor
`s:scale`	·	Scale Factor
`s:scalephi`	rad	Load Scaling
`s:pini_set`	MW	Nominal Active Power
`s:qini_set`	Mvar	Nominal Reactive Power
`s:prini_set`	MW	Active Power Setpoint, ph. A
`s:qrini_set`	Mvar	Reactive Power Setpoint, ph. A
`s:psini_set`	MW	Active Power Setpoint, ph. B
`s:qsini_set`	Mvar	Reactive Power Setpoint, ph. B
`s:ptini_set`	MW	Active Power Setpoint, ph. C
`s:qtini_set`	Mvar	Reactive Power Setpoint, ph. C
`s:scaler`	·	Scale Factor, ph. A
`s:scales`	·	Scale Factor, ph. B
`s:scalet`	·	Scale Factor, ph. C

ElmLod short-circuit results

Read after ComShc with GetAttribute. m: currents, voltages and powers, c: calculation parameter, n: bus result at a terminal.

Attribute	Unit	Description
`m:I:bus1`	kA	Short-Circuit Current, Magnitude
`m:phii:bus1`	deg	Phase Current, Angle
`m:i1:bus1`	p.u.	Positive-Sequence Current, Magnitude
`m:I1:bus1`	kA	Positive-Sequence Current, Magnitude
`m:phii1:bus1`	deg	Positive-Sequence Current, Angle
`m:P:bus1`	MW	Active Power
`m:Q:bus1`	Mvar	Reactive Power
`m:i1P:bus1`	p.u.	Positive-Sequence Active Current
`m:i1Q:bus1`	p.u.	Positive-Sequence Reactive Current
`m:I1P:bus1`	kA	Positive-Sequence Active Current
`m:I1Q:bus1`	kA	Positive-Sequence Reactive Current
`m:phiui:bus1`	deg	Angle between Voltage and Current
`m:phiu1i1:bus1`	deg	Angle between Voltage and Current in Positive-Sequence System
`m:Tfct:bus1`	s	Fault Clearing Time
`m:Ikss:bus1`	kA	Initial Short-Circuit Current
`m:ikss:bus1`	p.u.	Initial Short-Circuit Current, Magnitude
`m:Skss:bus1`	MVA	Initial Short-Circuit Power
`m:ip:bus1`	kA	Peak Short-Circuit Current
`m:maxIkss:bus1`	kA	Max. Initial Short-Circuit Current
`m:maxip:bus1`	kA	Max. Peak Short-Circuit Current
`m:maxIth:bus1`	kA	Max. Thermal equivalent Short-Circuit Current
`m:maxIb:bus1`	kA	Max. Breaking Current
`m:R:bus1`	Ohm	Fault Impedance, Real Part
`m:X:bus1`	Ohm	Fault Impedance, Imaginary Part
`m:Z:bus1`	Ohm	Fault Impedance, Magnitude
`m:phiz:bus1`	deg	Fault Impedance, Angle
`m:Rs:bus1`	Ohm	Source Impedance, Real Part
`m:Xs:bus1`	Ohm	Source Impedance, Imaginary Part
`m:Zs:bus1`	Ohm	Source Impedance, Magnitude
`m:phizs:bus1`	deg	Source Impedance, Angle
`m:BrkIpload:bus1`	%	Breaker Loading (peak)
`m:Ib:bus1`	kA	Short-Circuit Breaking Current
`m:Sb:bus1`	MVA	Short-Circuit Breaking Power
`m:Ith:bus1`	kA	Thermal equivalent Short-Circuit Current
`m:zSbase:bus1`	p.u.	Fault Impedance, Magnitude
`m:XtoR:bus1`	·	X/R ratio
`m:cosphiui:bus1`	·	cosphi
`m:BrkIbload:bus1`	%	Breaker Loading (breaking)
`m:BrkmaxIb:bus1`	kA	Max. Breaking Current (breaker time)
`m:Ik:bus1`	kA	Steady-State Short-Circuit Current
`m:I:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Short-Circuit Current, Magnitude
`m:phii:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Phase Current, Angle
`m:I0:bus1`	kA	Zero-Sequence Current, Magnitude
`m:I0x3:bus1`	kA	3*I0
`m:phii0:bus1`	deg	Zero-Sequence Current, Angle
`m:I2:bus1`	kA	Negative-Sequence Current, Magnitude
`m:phii2:bus1`	deg	Negative-Sequence Current, Angle
`m:P:bus1:A`per phase :A, :B, :C, unbalanced only	MW	Active Power
`m:Q:bus1:A`per phase :A, :B, :C, unbalanced only	Mvar	Reactive Power
`m:Psum:bus1`	MW	Total Active Power
`m:Qsum:bus1`	Mvar	Total Reactive Power
`m:cosphisum:bus1`	·	Total Power Factor
`m:P2:bus1`	MW	P2
`m:Q2:bus1`	Mvar	Q2
`m:P0:bus1`	MW	P0
`m:phiui:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle between Voltage and Current
`m:phiu0i0:bus1`	deg	Angle between Voltage and Current in Zero-Sequence System
`m:phiu2i2:bus1`	deg	Angle between Voltage and Current in Negative-Sequence System
`m:TfctPh:bus1:A`per phase :A, :B, :C, unbalanced only	s	Fault Clearing Time
`m:Ikss:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Initial Short-Circuit Current
`m:ikss:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Initial Short-Circuit Current, Magnitude
`m:Skss:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	Initial Short-Circuit Power
`m:Skssx3:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	3*Initial Short-Circuit Power
`m:ip:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Peak Short-Circuit Current
`m:Z:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Fault Impedance, Magnitude
`m:phiz:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Fault Impedance, Angle
`m:Zl:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Line-Line Fault Impedance, Magnitude
`m:phizl:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Line Fault Impedance, Angle
`m:Z0:bus1`	Ohm	Zero-Sequence Fault Impedance, Magnitude
`m:phiz0:bus1`	deg	Zero-Sequence Fault Impedance, Angle
`m:z0Sbase:bus1`	p.u.	Zero-Sequence Fault Impedance, Magnitude
`m:cosphiu1i1:bus1`	·	Positive-Sequence cosphi
`m:I0x3watt:bus1`	kA	Earth-Fault Residual Current
`m:I0x3var:bus1`	kA	Capacitive Earth-Fault Current
`m:Q0cap:bus1`	Mvar	Q0 capacitive
`m:Rfrel:bus1`	Ohm	Relay Impedance, Real Part
`m:Xfrel:bus1`	Ohm	Relay Impedance, Imaginary Part
`m:Zfrel:bus1`	Ohm	Relay Impedance, Magnitude
`m:phizfrel:bus1`	deg	Relay Impedance, Angle
`m:Zf:bus1`	Ohm	Meas. Fault Impedance, Magnitude
`m:phizf:bus1`	deg	Meas. Fault Impedance, Angle
`c:Rs`	Ohm	Static Resistance
`c:i_pure`	·	Purely inductive/capacitive
`c:icsrc`	·	Current Source/Impedance
`c:uss`	·	normPQext
`c:R`	p.u.	Resistance
`c:L`	p.u.	Inductance
`c:C`	p.u.	Capacitance
`c:C_lv`	p.u.	LV-Capacitance
`c:y1`	p.u.	Admittance
`c:i1`	p.u.	Harmonic current
`c:i1iec`	p.u.	Harmonic IEC current
`c:zd`	p.u.	Dynamic Impedance
`c:zs`	p.u.	Static Impedance
`c:Rd`	Ohm	Dynamic Resistance
`c:Xd`	Ohm	Dynamic Reactance
`c:Zd`	Ohm	Dynamic Impedance
`c:Xs`	Ohm	Static Reactance
`c:Zs`	Ohm	Static Impedance
`c:rnet`	p.u.	Total Resistance
`c:xnet`	p.u.	Total Reactance
`c:cn`	·	Connection Mode
`c:z0`	p.u.	z0
`c:Ra`	p.u.	Resistance, Phase a
`c:Rb`	p.u.	Resistance, Phase b
`c:Rc`	p.u.	Resistance, Phase c
`c:La`	p.u.	Inductance, Phase a
`c:Lb`	p.u.	Inductance, Phase b
`c:Lc`	p.u.	Inductance, Phase c
`c:Ca`	p.u.	Capacitance, Phase a
`c:Cb`	p.u.	Capacitance, Phase b
`c:Cc`	p.u.	Capacitance, Phase c
`c:y_a`	p.u.	Admittance, Phase a
`c:y_b`	p.u.	Admittance, Phase b
`c:y_c`	p.u.	Admittance, Phase c
`c:Ca_lv`	p.u.	LV-Capacitance, Phase a
`c:Cb_lv`	p.u.	LV-Capacitance, Phase b
`c:Cc_lv`	p.u.	LV-Capacitance, Phase c
`c:i_abc`	p.u.	Harmonic currents
`c:i_abc_iec`	p.u.	Harmonic IEC current
`c:i_ab`	p.u.	Harmonic currents
`c:i_ab_iec`	p.u.	Harmonic IEC current
`n:ur:bus1`	p.u.	Voltage, Real Part
`n:ui:bus1`	p.u.	Voltage, Imaginary Part
`n:u:bus1`	p.u.	Voltage, Magnitude
`n:upc:bus1`	%	Voltage, Magnitude
`n:du:bus1`	%	Voltage Deviation
`n:U:bus1`	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1`	deg	Voltage, Angle
`n:Ul:bus1`	kV	Line-Line Voltage, Magnitude
`n:u1:bus1`	p.u.	Voltage, Magnitude
`n:u1pc:bus1`	%	Voltage, Magnitude
`n:u1r:bus1`	p.u.	Positive-Sequence Voltage, Real Part
`n:u1i:bus1`	p.u.	Positive-Sequence Voltage, Imaginary Part
`n:Ikss:bus1`	kA	Initial Short-Circuit Current
`n:I:bus1`	kA	Short-Circuit Current
`n:phii:bus1`	deg	Phase Current, Angle
`n:Skss:bus1`	MVA	Initial Short-Circuit Power
`n:ip:bus1`	kA	Peak Short-Circuit Current
`n:Ib:bus1`	kA	Short-Circuit Breaking Current
`n:Sb:bus1`	MVA	Short-Circuit Breaking Power
`n:idc:bus1`	kA	Decaying Component
`n:Ith:bus1`	kA	Thermal equivalent Short-Circuit Current
`n:R1toX1:bus1`	·	R1/X1 ratio (Zk")
`n:X1toR1:bus1`	·	X1/R1 ratio (Zk")
`n:R:bus1`	Ohm	Short-Circuit Impedance, Real Part
`n:X:bus1`	Ohm	Short-Circuit Impedance, Imaginary Part
`n:Z:bus1`	Ohm	Short-Circuit Impedance, Magnitude
`n:phiz:bus1`	deg	Short-Circuit Impedance, Angle
`n:urpref:bus1`	p.u.	Pre-fault Voltage, Real Part
`n:uipref:bus1`	p.u.	Pre-fault Voltage, Imaginary Part
`n:upref:bus1`	p.u.	Pre-fault Voltage, Magnitude
`n:uprefpc:bus1`	%	Pre-fault Voltage, Magnitude
`n:Upref:bus1`	kV	Line-Ground Pre-fault Voltage, Magnitude
`n:Ulpref:bus1`	kV	Line-Line Pre-fault Voltage, Magnitude
`n:phiupref:bus1`	deg	Pre-fault Voltage, Angle
`n:phiui:bus1`	deg	Angle between Voltage and Current
`n:Ithload:bus1`	%	Loading, Thermal equivalent Current
`n:Ipload:bus1`	%	Loading, Peak Short-Circuit Current
`n:Ithrtk:bus1`	kA	Rated Short-Time Current (Tk)
`n:XtoR:bus1`	·	X/R ratio (peak)
`n:RtoX:bus1`	·	R/X ratio (peak)
`n:XtoR_b:bus1`	·	X/R ratio (dc)
`n:RtoX_b:bus1`	·	R/X ratio (dc)
`n:fctof_b:bus1`	·	Equivalent Frequency fc/f (dc)
`n:rSbase:bus1`	p.u.	Short-Circuit Impedance, Real Part
`n:xSbase:bus1`	p.u.	Short-Circuit Impedance, Imaginary Part
`n:zSbase:bus1`	p.u.	Short-Circuit Impedance, Magnitude
`n:Tn:bus1`	ms	Grid Time Constant
`n:Ik:bus1`	kA	Steady-State Short-Circuit Current
`n:cfac:bus1`	·	Voltage Factor
`n:Iasy:bus1`	kA	Asymmetrical Breaking Current
`n:ur:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Real Part
`n:ui:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Imaginary Part
`n:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Magnitude
`n:upc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Ground Voltage, Magnitude
`n:du:bus1:A`per phase :A, :B, :C, unbalanced only	%	Voltage Deviation
`n:U:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Ground Voltage, Angle
`n:ul:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Line Voltage, Magnitude
`n:ulpc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Line Voltage, Magnitude
`n:Ul:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Line Voltage, Magnitude
`n:phiul:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Line Voltage, Angle
`n:u0:bus1`	p.u.	Zero-Sequence Voltage, Magnitude
`n:U0:bus1`	kV	Zero-Sequence Voltage, Magnitude
`n:U0x3:bus1`	kV	3*U0
`n:phiu0:bus1`	deg	Zero-Sequence Voltage, Angle
`n:U1:bus1`	kV	Line-Ground Positive-Sequence Voltage, Magnitude
`n:phiu1:bus1`	deg	Positive-Sequence Voltage, Angle
`n:u2:bus1`	p.u.	Negative-Sequence Voltage, Magnitude
`n:U2:bus1`	kV	Line-Ground Negative-Sequence Voltage, Magnitude
`n:phiu2:bus1`	deg	Negative-Sequence Voltage, Angle
`n:U1l:bus1`	kV	Line-Line Positive-Sequence Voltage, Magnitude
`n:U2l:bus1`	kV	Line-Line Negative-Sequence Voltage, Magnitude
`n:uln:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Neutral Voltage, Magnitude
`n:Uln:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Neutral Voltage, Magnitude
`n:phiuln:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Neutral Voltage, Angle
`n:un:bus1`	p.u.	Neutral-Ground Voltage, Magnitude
`n:Un:bus1`	kV	Neutral-Ground Voltage, Magnitude
`n:phiun:bus1`	deg	Neutral-Ground Voltage, Angle
`n:upht:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Technology dependent Voltage, Magnitude
`n:Upht:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Phase Technology dependent Voltage, Magnitude
`n:Ikss:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Initial Short-Circuit Current
`n:I:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Short-Circuit Current
`n:phii:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Phase Current, Angle
`n:Skss:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	Initial Short-Circuit Power
`n:Skssx3:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	3*Initial Short-Circuit Power
`n:ip:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Peak Short-Circuit Current
`n:Ib:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Short-Circuit Breaking Current
`n:Sb:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	Short-Circuit Breaking Power
`n:Ith:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Thermal equivalent Short-Circuit Current
`n:Ithmax:bus1`	kA	Max. Thermal equivalent Short-Circuit Current
`n:R0:bus1`	Ohm	Zero-Sequence Impedance, Real Part
`n:X0:bus1`	Ohm	Zero-Sequence Impedance, Imaginary Part
`n:Z0:bus1`	Ohm	Zero-Sequence Impedance, Magnitude
`n:phiz0:bus1`	deg	Zero-Sequence Impedance, Angle
`n:r0Sbase:bus1`	p.u.	Zero-Sequence Impedance, Real Part
`n:x0Sbase:bus1`	p.u.	Zero-Sequence Impedance, Imaginary Part
`n:z0Sbase:bus1`	p.u.	Zero-Sequence Impedance, Magnitude
`n:R1:bus1`	Ohm	Positive-Sequence Impedance, Real Part
`n:X1:bus1`	Ohm	Positive-Sequence Impedance, Imaginary Part
`n:Z1:bus1`	Ohm	Positive-Sequence Impedance, Magnitude
`n:phiz1:bus1`	deg	Positive-Sequence Impedance, Angle
`n:r1Sbase:bus1`	p.u.	Positive-Sequence Impedance, Real Part
`n:x1Sbase:bus1`	p.u.	Positive-Sequence Impedance, Imaginary Part
`n:z1Sbase:bus1`	p.u.	Positive-Sequence Impedance, Magnitude
`n:R2:bus1`	Ohm	Negative-Sequence Impedance, Real Part
`n:X2:bus1`	Ohm	Negative-Sequence Impedance, Imaginary Part
`n:Z2:bus1`	Ohm	Negative-Sequence Impedance, Magnitude
`n:phiz2:bus1`	deg	Negative-Sequence Impedance, Angle
`n:r2Sbase:bus1`	p.u.	Negative-Sequence Impedance, Real Part
`n:x2Sbase:bus1`	p.u.	Negative-Sequence Impedance, Imaginary Part
`n:z2Sbase:bus1`	p.u.	Negative-Sequence Impedance, Magnitude
`n:R0toX0:bus1`	·	R0/X0 ratio (Zk")
`n:X0toR0:bus1`	·	X0/R0 ratio (Zk")
`n:R2toX2:bus1`	·	R2/X2 ratio (Zk")
`n:X2toR2:bus1`	·	X2/R2 ratio (Zk")
`n:R:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Resistance, Line-Ground
`n:X:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Reactance, Line-Ground
`n:Z:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Impedance, Line-Ground
`n:phiz:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle of Network Impedance, Line-Ground
`n:Rl:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Resistance, Line-Line
`n:Xl:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Reactance, Line-Line
`n:Zl:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Impedance, Line-Line
`n:phizl:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle of Network Impedance, Line-Line
`n:Rln:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Resistance, Line-Neutral
`n:Xln:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Reactance, Line-Neutral
`n:Zln:bus1:A`per phase :A, :B, :C, unbalanced only	Ohm	Network Impedance, Line-Neutral
`n:phizln:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle of Network Impedance, Line-Neutral
`n:Rn:bus1`	Ohm	Network Resistance, Neutral
`n:Xn:bus1`	Ohm	Network Reactance, Neutral
`n:Zn:bus1`	Ohm	Network Impedance, Neutral
`n:phizn:bus1`	deg	Angle of Network Impedance, Neutral
`n:eff:bus1:A`per phase :A, :B, :C, unbalanced only	·	Earth Fault Factor
`n:X0toX1:bus1`	·	X0/X1
`n:In:bus1`	kA	Neutral Current, Magnitude
`n:phiin:bus1`	deg	Neutral Current, Angle
`n:I0:bus1`	kA	Zero-Sequence Current, Magnitude
`n:I0x3:bus1`	kA	3*I0
`n:phii0:bus1`	deg	Zero-Sequence Current, Angle
`n:I1:bus1`	kA	Positive-Sequence Current, Magnitude
`n:phii1:bus1`	deg	Positive-Sequence Current, Angle
`n:I2:bus1`	kA	Negative-Sequence Current, Magnitude
`n:phii2:bus1`	deg	Negative-Sequence Current, Angle
`n:urpref:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Pre-fault Voltage, Real Part
`n:uipref:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Pre-fault Voltage, Imaginary Part
`n:upref:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Pre-fault Voltage, Magnitude
`n:uprefpc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Pre-fault Voltage, Magnitude
`n:Upref:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Ground Pre-fault Voltage, Magnitude
`n:Ulpref:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Line Pre-fault Voltage, Magnitude
`n:phiupref:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Pre-fault Voltage, Angle
`n:phiui:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle between Voltage and Current
`n:phiu1i1:bus1`	deg	Angle between Voltage and Current in positive sequence system
`n:phiu2i2:bus1`	deg	Angle between Voltage and Current in negative sequence system
`n:phiu0i0:bus1`	deg	Angle between Voltage and Current in zero-sequence system
`n:Ik:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Steady-State Short-Circuit Current
`n:in:bus1`	p.u.	Neutral Current, Magnitude
`n:i0r:bus1`	p.u.	Zero-Sequence Current, Real Part
`n:i0i:bus1`	p.u.	Zero-Sequence Current, Imaginary Part
`n:i0:bus1`	p.u.	Zero-Sequence Current, Magnitude
`n:i1r:bus1`	p.u.	Positive-Sequence Current, Real Part
`n:i1i:bus1`	p.u.	Positive-Sequence Current, Imaginary Part
`n:i1:bus1`	p.u.	Positive-Sequence Current, Magnitude
`n:i2r:bus1`	p.u.	Negative-Sequence Current, Real Part
`n:i2i:bus1`	p.u.	Negative-Sequence Current, Imaginary Part
`n:i2:bus1`	p.u.	Negative-Sequence Current, Magnitude

ElmLod rms simulation results

Read after ComInc (RMS) with GetAttribute. m: currents, voltages and powers, c: calculation parameter, n: bus result at a terminal, s: signal (state or model variable).

Attribute	Unit	Description
`m:urnet:bus1`	p.u.	Voltage, Real Part, referred to network
`m:uinet:bus1`	p.u.	Voltage, Imaginary Part, referred to network
`m:u1r:bus1`	p.u.	Positive-Sequence-Voltage, Real Part
`m:u1i:bus1`	p.u.	Positive-Sequence-Voltage, Imaginary Part
`m:u1:bus1`	p.u.	Positive-Sequence-Voltage, Magnitude
`m:U1:bus1`	kV	Line-Ground Positive-Sequence-Voltage, Magnitude
`m:U1l:bus1`	kV	Line-Line Positive-Sequence-Voltage, Magnitude
`m:phiu1:bus1`	deg	Positive-Sequence-Voltage, Angle
`m:irnet:bus1`	p.u.	Current, Real Part, referred to network
`m:iinet:bus1`	p.u.	Current, Imaginary Part, referred to network
`m:inet:bus1`	p.u.	Current, Magnitude, referred to network
`m:I:bus1`	kA	Current, Magnitude
`m:phii:bus1`	deg	Current, Angle
`m:i1r:bus1`	p.u.	Positive-Sequence Current, Real Part
`m:i1i:bus1`	p.u.	Positive-Sequence Current, Imaginary Part
`m:i1:bus1`	p.u.	Positive-Sequence Current, Magnitude
`m:I1:bus1`	kA	Positive-Sequence Current, Magnitude
`m:phii1:bus1`	deg	Positive-Sequence Current, Angle
`m:P:bus1`	MW	Active Power
`m:Q:bus1`	Mvar	Reactive Power
`m:S:bus1`	MVA	Apparent Power
`m:cosphi:bus1`	·	Power Factor
`m:tanphi:bus1`	·	tan(phi)
`m:Psum:bus1`	MW	Total Active Power
`m:Qsum:bus1`	Mvar	Total Reactive Power
`m:Ssum:bus1`	MVA	Total Apparent Power
`m:cosphisum:bus1`	·	Total Power Factor
`m:tanphisum:bus1`	·	Total tan(phi)
`m:i1P:bus1`	p.u.	Positive-Sequence Active Current
`m:i1Q:bus1`	p.u.	Positive-Sequence Reactive Current
`m:I1P:bus1`	kA	Positive-Sequence Active Current
`m:I1Q:bus1`	kA	Positive-Sequence Reactive Current
`m:ur:bus1`	p.u.	Voltage, Real Part
`m:ui:bus1`	p.u.	Voltage, Imaginary Part
`m:u:bus1`	p.u.	Voltage, Magnitude
`m:ir:bus1`	p.u.	Current, Real Part
`m:ii:bus1`	p.u.	Current, Imaginary Part
`m:i:bus1`	p.u.	Current, Magnitude
`m:phiui:bus1`	deg	Angle between Voltage and Current
`m:phiu1i1:bus1`	deg	Angle between Voltage and Current in positive sequence system
`m:Tfct:bus1`	s	Fault Clearing Time
`m:Brkload:bus1`	%	Breaker Loading
`m:Spu:bus1`	MVA/p.u.	Apparent Power per p.u. Voltage
`m:urnet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Real Part, referred to network
`m:uinet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Imaginary Part, referred to network
`m:u0:bus1`	p.u.	Zero-Sequence-Voltage, Magnitude
`m:phiu0:bus1`	deg	Zero-Sequence-Voltage, Angle
`m:u2:bus1`	p.u.	Negative-Sequence-Voltage, Magnitude
`m:phiu2:bus1`	deg	Negative-Sequence-Voltage, Angle
`m:irnet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Real Part
`m:iinet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Imaginary Part
`m:inet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Magnitude
`m:I:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Phase Current, Magnitude
`m:phii:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Phase Current, Angle
`m:i0r:bus1`	p.u.	Zero-Sequence Current, Real Part
`m:i0i:bus1`	p.u.	Zero-Sequence Current, Imaginary Part
`m:i0:bus1`	p.u.	Zero-Sequence Current, Magnitude
`m:I0:bus1`	kA	Zero-Sequence Current, Magnitude
`m:I0x3:bus1`	kA	3*I0
`m:phii0:bus1`	deg	Zero-Sequence Current, Angle
`m:i2r:bus1`	p.u.	Negative-Sequence Current, Real Part
`m:i2i:bus1`	p.u.	Negative-Sequence Current, Imaginary Part
`m:i2:bus1`	p.u.	Negative-Sequence Current, Magnitude
`m:I2:bus1`	kA	Negative-Sequence Current, Magnitude
`m:phii2:bus1`	deg	Negative-Sequence Current, Angle
`m:P:bus1:A`per phase :A, :B, :C, unbalanced only	MW	Active Power
`m:Q:bus1:A`per phase :A, :B, :C, unbalanced only	Mvar	Reactive Power
`m:S:bus1:A`per phase :A, :B, :C, unbalanced only	MVA	Apparent Power
`m:cosphi:bus1:A`per phase :A, :B, :C, unbalanced only	·	Power Factor
`m:tanphi:bus1:A`per phase :A, :B, :C, unbalanced only	·	tan(phi)
`m:Pln:bus1:A`per phase :A, :B, :C, unbalanced only	MW	Active Power (Line-Neutral)
`m:Qln:bus1:A`per phase :A, :B, :C, unbalanced only	Mvar	Reactive Power (Line-Neutral)
`m:P1:bus1`	MW	Positive Sequence Active Power
`m:Q1:bus1`	Mvar	Positive Sequence Reactive Power
`m:P2:bus1`	MW	Negative Sequence Active Power
`m:Q2:bus1`	Mvar	Negative Sequence Reactive Power
`m:P0:bus1`	MW	Zero Sequence Active Power
`m:Q0:bus1`	Mvar	Zero Sequence Reactive Power
`m:i2P:bus1`	p.u.	Negative-Sequence Active Current
`m:i2Q:bus1`	p.u.	Negative-Sequence Reactive Current
`m:I2P:bus1`	kA	Negative-Sequence Active Current
`m:I2Q:bus1`	kA	Negative-Sequence Reactive Current
`m:ur:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Real Part
`m:ui:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Imaginary Part
`m:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, Magnitude
`m:ir:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Real Part
`m:ii:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Imaginary Part
`m:i:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, Magnitude
`m:phiui:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Angle between Voltage and Current
`m:phiu0i0:bus1`	deg	Angle between Voltage and Current in zero-sequence system
`m:phiu2i2:bus1`	deg	Angle between Voltage and Current in negative sequence system
`m:TfctPh:bus1:A`per phase :A, :B, :C, unbalanced only	s	Fault Clearing Time
`m:BrkloadPh:bus1:A`per phase :A, :B, :C, unbalanced only	%	Breaker Loading
`c:hpi`	rad/s	pini
`c:pini`	MW	loddy_l
`c:lodst_l`	·	Static
`c:loddy_l`	·	Dynamic
`c:kpf`	·	Static Frequency Dependence
`c:kqf`	·	Static Frequency Dependence
`c:t1`	s	Dynamic Load Time Constant
`c:sd0`	MVA	Nominal power of dynamic load
`c:sd00`	MVA	Nominal power of dynamic load
`c:udmax`	p.u.	Upper Voltage Limit
`c:udmin`	p.u.	Lower Voltage Limit
`c:fe`	p.u.	Electrical Frequency
`c:scale`	·	bQ
`c:lodsp_l`	·	Special
`c:tpu`	·	Transient Voltage Dependence
`c:tqu`	s	Transient Voltage Dependence
`c:ssp0`	MVA	Nominal power of special load
`c:ssp00`	MVA	Nominal power of special load
`c:u0`	p.u.	Nominal voltage
`c:i_nln`	·	Internal Flag
`c:kpu0`	·	Volt. Dependence I on P
`c:kqu0`	·	Volt. Dependence I on Q
`c:kpu1`	·	Volt. Dependence II on P
`c:kqu1`	·	Volt. Dependence II on Q
`c:kpu`	·	Volt. Dependence III on P
`c:kqu`	·	Volt. Dependence III on Q
`c:aP`	·	Percent of Volt. Dep. I on P
`c:bP`	·	Percent of Volt. Dep. II on P
`c:aQ`	·	Percent of Volt. Dep. I on Q
`c:bQ`	·	Percent of Volt. Dep. II on Q
`c:motorA`	CalLodwecc1pac,CalLodweccasm	Motor A
`c:motorB`	CalLodwecc1pac,CalLodweccasm	Motor B
`c:motorC`	CalLodwecc1pac,CalLodweccasm	Motor C
`c:motorD`	CalLodwecc1pac,CalLodweccasm	Motor D
`c:Tap`	p.u.	Transformer tap
`c:Rfdr`	p.u.	Feeder R (p.u. of MVA base)
`c:Xfdr`	p.u.	Feeder X (p.u. of MVA base)
`c:Bfdr`	p.u.	Value of the total feeder reactive compensation
`c:Vls`	p.u.	Voltage at substation low-side bus
`c:Vld`	p.u.	Voltage at load end of feeder
`c:Pst`	·	Pst
`c:Qst`	·	Qst
`c:Pel`	·	Pel
`c:Qel`	·	Qel
`c:Fv1`	·	Fv1
`c:qini`	Mvar	Nominal Reactive Power
`c:tpf`	s	Transient Frequency Dependence
`c:tqf`	s	Transient Frequency Dependence
`c:glod`	p.u.	Conductance
`c:gs0`	p.u.	Conductance
`c:bs0`	p.u.	Susceptance
`c:x`	p.u.	Reactance
`c:r`	p.u.	Resistance
`c:slip`	p.u.	Slip
`c:s0pu`	p.u.	Slip at Normal Operation Point
`c:scrpu`	p.u.	Critical Slip
`c:tm00`	p.u.	Ratio of Dynamic Load (Normal Operating Torque)
`c:Tj`	s	Acceleration time constant
`c:i_dyn`	·	i_dyn
`c:xme`	p.u.	Electrical Torque
`c:xmt0`	p.u.	Initial mechanical torque
`c:tm1`	·	Mechanical Torque Exponent
`c:speed0`	p.u.	Initial speed
`c:xmt`	p.u.	Mechanical Torque
`c:ushed`	p.u.	Voltage setting for load shedding
`c:shape`	·	Shape of Load Shedding Probability Function
`c:fshed`	p.u.	Load-Shedding Factor
`c:ureclose`	p.u.	Voltage setting for reclosing
`c:currr`	p.u.	Rotor Current, Real Part
`c:curri`	p.u.	Rotor Current, Imaginary Part
`c:cn`	·	Connection Mode
`c:sr`	MW	Complex Power (P+jQ), ph. A
`c:ss`	MW	Complex Power (P+jQ), ph. B
`c:st`	MW	Complex Power (P+jQ), ph. C
`c:yr`	p.u.	Load Admittance, ph. A
`c:ys`	p.u.	Load Admittance, ph. B
`c:yt`	p.u.	Load Admittance, ph. C
`c:yr0`	p.u.	Load Admittance, ph. A
`c:ys0`	p.u.	Load Admittance, ph. B
`c:yt0`	p.u.	Load Admittance, ph. C
`c:z0`	p.u.	z0
`c:Fma`	·	Motor A fraction
`c:Fmb`	·	Motor B fraction
`c:Fmc`	·	Motor C fraction
`c:Fmd`	·	Motor D fraction
`c:Fel`	·	Electronic load fraction
`c:Fst`	·	Static load fraction
`n:ur:bus1`	p.u.	Voltage, Real Part
`n:ui:bus1`	p.u.	Voltage, Imaginary Part
`n:u:bus1`	p.u.	Voltage, Magnitude
`n:upc:bus1`	%	Voltage, Magnitude
`n:du:bus1`	%	Voltage Deviation
`n:U:bus1`	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1`	deg	Voltage, Angle
`n:phiurel:bus1`	deg	Voltage, Relative Angle
`n:Ul:bus1`	kV	Line-Line Voltage, Magnitude
`n:u1:bus1`	p.u.	Voltage, Magnitude
`n:u1pc:bus1`	%	Voltage, Magnitude
`n:u1r:bus1`	p.u.	Positive-Sequence Voltage, Real Part
`n:u1i:bus1`	p.u.	Positive-Sequence Voltage, Imaginary Part
`n:ishc:bus1`	p.u.	Short-Circuit Current, magnitude
`n:Ishc:bus1`	kA	Short-Circuit Current, magnitude
`n:fe:bus1`	p.u.	Electrical Frequency
`n:dfehz:bus1`	Hz	Deviation of the El. Frequency
`n:fehz:bus1`	Hz	Electrical Frequency
`n:frnom:bus1`	Hz	Nominal Frequency
`n:ishcr:bus1`	p.u.	Short-Circuit Current, real
`n:ishci:bus1`	p.u.	Short-Circuit Current, imag
`n:dfedt:bus1`	p.u./s	Derivative of El. Frequency
`n:ur:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Real Part
`n:ui:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Imaginary Part
`n:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Ground Voltage, Magnitude
`n:upc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Ground Voltage, Magnitude
`n:du:bus1:A`per phase :A, :B, :C, unbalanced only	%	Voltage Deviation
`n:U:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Ground Voltage, Angle
`n:ul:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Line Voltage, Magnitude
`n:ulpc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Line Voltage, Magnitude
`n:Ul:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Line Voltage, Magnitude
`n:phiul:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Line Voltage, Angle
`n:u0:bus1`	p.u.	Zero-Sequence Voltage, Magnitude
`n:U0:bus1`	kV	Zero-Sequence Voltage, Magnitude
`n:U0x3:bus1`	kV	3*U0
`n:phiu0:bus1`	deg	Zero-Sequence Voltage, Angle
`n:U1:bus1`	kV	Line-Ground Positive-Sequence Voltage, Magnitude
`n:phiu1:bus1`	deg	Positive-Sequence Voltage, Angle
`n:u2:bus1`	p.u.	Negative-Sequence Voltage, Magnitude
`n:U2:bus1`	kV	Line-Ground Negative-Sequence Voltage, Magnitude
`n:phiu2:bus1`	deg	Negative-Sequence Voltage, Angle
`n:U1l:bus1`	kV	Line-Line Positive-Sequence Voltage, Magnitude
`n:U2l:bus1`	kV	Line-Line Negative-Sequence Voltage, Magnitude
`n:uln:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Neutral Voltage, Magnitude
`n:Uln:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Neutral Voltage, Magnitude
`n:phiuln:bus1:A`per phase :A, :B, :C, unbalanced only	deg	Line-Neutral Voltage, Angle
`n:un:bus1`	p.u.	Neutral-Ground Voltage, Magnitude
`n:Un:bus1`	kV	Neutral-Ground Voltage, Magnitude
`n:phiun:bus1`	deg	Neutral-Ground Voltage, Angle
`n:upht:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Technology dependent Voltage, Magnitude
`n:Upht:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Phase Technology dependent Voltage, Magnitude
`n:um:bus1`	p.u.	Average-Voltage, Magnitude
`n:Um:bus1`	kV	Average-Voltage, Magnitude
`n:ishc:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Short-Circuit Current, magnitude
`n:Ishc:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Short-Circuit Current, magnitude
`n:inshc:bus1`	p.u.	Neutral Short-Circuit Current, magnitude
`n:Inshc:bus1`	kA	Neutral Short-Circuit Current, magnitude
`n:ishcr:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Short-Circuit Current, real
`n:ishci:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Short-Circuit Current, imag
`s:xu`	p.u.	State Variable
`s:Pext`	MW	Active Power Input
`s:Qext`	Mvar	Reactive Power Input
`s:fref`	p.u.	Reference Frequency
`s:xf`	p.u.	State Variable
`s:speed`	p.u.	Speed
`s:xmdm`	p.u.	MDM-Torque
`s:psirr`	p.u.	Rotor Flux, Real Part
`s:psiri`	p.u.	Rotor Flux, Imaginary Part
`s:fshedin`	p.u.	Load-Shedding Factor

ElmLod emt simulation results

Read after ComInc (EMT) with GetAttribute. m: currents, voltages and powers, c: calculation parameter, n: bus result at a terminal, s: signal (state or model variable).

Attribute	Unit	Description
`m:u0:bus1`	p.u.	Zero-Sequence-Voltage
`m:u1r:bus1`	p.u.	Voltage Phasor, Real Part
`m:u1i:bus1`	p.u.	Voltage Phasor, Imaginary Part
`m:u1:bus1`	p.u.	Voltage Phasor, Magnitude
`m:U1:bus1`	kV	Line-Ground Voltage Phasor, Magnitude
`m:U1l:bus1`	kV	Line-Line Voltage Phasor, Magnitude
`m:phiu1:bus1`	deg	Voltage Phasor, Angle
`m:inet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current, referred to network
`m:I:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Phase Current
`m:i0:bus1`	p.u.	Zero-Sequence Current
`m:I0:bus1`	kA	Zero-Sequence Current
`m:I0x3:bus1`	kA	3*I0
`m:i1r:bus1`	p.u.	Current Phasor, Real Part
`m:i1i:bus1`	p.u.	Current Phasor, Imaginary Part
`m:i1:bus1`	p.u.	Current Phasor, Magnitude
`m:I1:bus1`	kA	Current Phasor, Magnitude
`m:phii1:bus1`	deg	Current Phasor, Angle
`m:P:bus1:A`per phase :A, :B, :C, unbalanced only	MW	Active Power
`m:Psum:bus1`	MW	Power-Phasor, Active Power
`m:Qsum:bus1`	Mvar	Power Phasor, Reactive Part
`m:Ssum:bus1`	MVA	Power Phasor, Apparent Power
`m:i1P:bus1`	p.u.	Current Phasor, Active Current
`m:i1Q:bus1`	p.u.	Current Phasor, Reactive Current
`m:I1P:bus1`	kA	Current Phasor, Active Current
`m:I1Q:bus1`	kA	Current Phasor, Reactive Current
`m:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage
`m:i:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Current
`m:phiu1i1:bus1`	deg	Angle between Voltage and Current Phasor
`m:Tfct:bus1`	s	Fault Clearing Time
`m:TfctPh:bus1:A`per phase :A, :B, :C, unbalanced only	s	Fault Clearing Time
`m:unet:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage, referred to network
`m:cosphi1:bus1`	·	Power-Phasor, Power-Factor
`c:frnom`	Hz	Nominal Frequency
`c:hpi`	rad/s	Nominal angular frequency
`c:pini`	MW	ys0
`c:ys0:A`per phase :A, :B, :C, unbalanced only	p.u.	Admittance
`c:scale`	·	Scale Factor of Load Shedding Probability Function
`c:u0`	p.u.	Nominal Voltage
`c:kpu0`	·	Volt. Dependence I on P
`c:kqu0`	·	Volt. Dependence I on Q
`c:kpu1`	·	Volt. Dependence II on P
`c:kqu1`	·	Volt. Dependence II on Q
`c:kpu`	·	Volt. Dependence III on P
`c:kqu`	·	Volt. Dependence III on Q
`c:aP`	·	Percent of Volt. Dep. I on P
`c:bP`	·	Percent of Volt. Dep. II on P
`c:aQ`	·	Percent of Volt. Dep. I on Q
`c:bQ`	·	Percent of Volt. Dep. II on Q
`c:qini`	Mvar	Nominal Reactive Power
`c:Ra`	Ohm	Resistance
`c:Rb`	Ohm	Resistance
`c:Rc`	Ohm	Resistance
`c:La`	mH	Inductance
`c:Lb`	mH	Inductance
`c:Lc`	mH	Inductance
`c:Ca`	uF	Capacitance
`c:Cb`	uF	Capacitance
`c:Cc`	uF	Capacitance
`c:R`	Ohm	Resistance
`c:R:A`per phase :A, :B, :C, unbalanced only	p.u.	normPQext
`c:L`	mH	Inductance
`c:L:A`per phase :A, :B, :C, unbalanced only	p.u.	normPQext
`c:C`	uF	Capacitance
`c:C:A`per phase :A, :B, :C, unbalanced only	p.u.	normPQext
`c:glod`	p.u.	Conductance
`c:x`	p.u.	Reactance
`c:r`	p.u.	Resistance
`c:slip`	p.u.	Slip
`c:cnm`	·	Connection
`c:s0pu`	p.u.	Slip at Normal Operation Point
`c:scrpu`	p.u.	Critical Slip
`c:tm00`	p.u.	Ratio of Dynamic Load (Normal Operating Torque)
`c:Tj`	s	Acceleration time constant
`c:i_dyn`	·	i_dyn
`c:xme`	p.u.	Electrical Torque
`c:xmt0`	p.u.	Initial mechanical torque
`c:tm1`	·	Mechanical Torque Exponent
`c:speed0`	p.u.	Initial speed
`c:xmt`	p.u.	Mechanical Torque
`c:ushed`	p.u.	Voltage setting for load shedding
`c:shape`	·	Shape of Load Shedding Probability Function
`c:fshed`	p.u.	Load-Shedding Factor
`c:ureclose`	p.u.	Voltage setting for reclosing
`c:pinir`	MW	Nominal Active Power, ph. A
`c:qinir`	Mvar	Nominal Reactive Power, ph. A
`c:pinis`	MW	Nominal Active Power, ph. B
`c:qinis`	Mvar	Nominal Reactive Power, ph. B
`c:pinit`	MW	Nominal Active Power, ph. C
`c:qinit`	Mvar	Nominal Reactive Power, ph. C
`c:u0abc:A`per phase :A, :B, :C, unbalanced only	p.u.	u0abc
`n:u:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Phase Voltage
`n:upc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Phase Voltage
`n:U:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Phase Voltage
`n:ul:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Line Voltage
`n:ulpc:bus1:A`per phase :A, :B, :C, unbalanced only	%	Line-Line Voltage
`n:Ul:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Line Voltage
`n:u0:bus1`	p.u.	Zero-Sequence-Voltage
`n:U0:bus1`	kV	Zero-Sequence-Voltage
`n:U0x3:bus1`	kV	3*U0
`n:u1:bus1`	p.u.	Voltage Phasor, Magnitude
`n:u1pc:bus1`	%	Voltage Phasor, Magnitude
`n:u1r:bus1`	p.u.	Voltage Phasor, Real Part
`n:u1i:bus1`	p.u.	Voltage Phasor, Imaginary Part
`n:U1:bus1`	kV	Voltage Phasor, Magnitude
`n:phiu1:bus1`	deg	Voltage Phasor, Angle
`n:U1l:bus1`	kV	Line-Line Voltage Phasor, Magnitude
`n:uln:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Line-Neutral Voltage
`n:Uln:bus1:A`per phase :A, :B, :C, unbalanced only	kV	Line-Neutral Voltage
`n:un:bus1`	p.u.	Neutral-Ground Voltage
`n:Un:bus1`	kV	Neutral-Ground Voltage
`n:ishc:bus1:A`per phase :A, :B, :C, unbalanced only	p.u.	Short-Circuit Current
`n:Ishc:bus1:A`per phase :A, :B, :C, unbalanced only	kA	Short-Circuit Current
`n:inshc:bus1`	p.u.	Neutral Short-Circuit Current, magnitude
`n:Inshc:bus1`	kA	Neutral Short-Circuit Current, magnitude
`n:fe:bus1`	p.u.	Electrical Frequency
`n:dfehz:bus1`	Hz	Deviation of the El. Frequency
`n:fehz:bus1`	Hz	Electrical Frequency
`n:frnom:bus1`	Hz	Nominal Frequency
`s:Rin`	Ohm	Resistance (Input)
`s:Lin`	mH	Inductance (Input)
`s:Cin`	uF	Capacitance (Input)
`s:Rin_A`	Ohm	Resistance (Input)
`s:Rin_B`	Ohm	Resistance (Input)
`s:Lin_A`	mH	Inductance (Input)
`s:Lin_B`	mH	Inductance (Input)
`s:Cin_A`	uF	Capacitance (Input)
`s:Cin_B`	uF	Capacitance (Input)
`s:Rin_C`	Ohm	Resistance (Input)
`s:Lin_C`	mH	Inductance (Input)
`s:Cin_C`	uF	Capacitance (Input)
`s:speed`	p.u.	Speed
`s:xmdm`	p.u.	MDM-Torque
`s:fshedin`	p.u.	Load-Shedding Factor
`s:psir`	p.u.	Flux, real part
`s:psii`	p.u.	Flux, imaginary part

ElmLod dc load flow results

Read after ComLdf (DC) with GetAttribute. m: currents, voltages and powers, c: calculation parameter, n: bus result at a terminal, s: signal (state or model variable).

Attribute	Unit	Description
`m:P:bus1`	MW	Active Power
`m:Q:bus1`	Mvar	Reactive Power
`c:pini`	MW	Nominal Active Power
`c:scale0`	·	Initial Scale Factor
`c:ncust`	·	Number of Connected Customers
`c:i_rem`	·	Remote Control
`c:zonescale`	·	Zone Scale Factor
`c:iRefElement`	·	Reference Element
`c:Pmism`	MW	Active Power Mismatch
`c:Ploss`	MW	Losses (total)
`c:Qloss`	Mvar	Reactive-Losses (total)
`c:Pnom`	MW	Nominal Active Power
`c:Ppeak`	MW	Peak Active Power
`c:p`	MW	Power
`n:u:bus1`	p.u.	Voltage, Magnitude
`n:upc:bus1`	%	Voltage, Magnitude
`n:U:bus1`	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1`	deg	Voltage, Angle
`n:phiurel:bus1`	deg	Voltage, Relative Angle
`n:Ul:bus1`	kV	Line-Line Voltage, Magnitude
`n:u1:bus1`	p.u.	Voltage, Magnitude
`n:Pgen:bus1`	MW	Generation, Active Power
`n:Pmot:bus1`	MW	Motor Load, Active Power
`n:Pload:bus1`	MW	General Load, Active Power
`n:Pcomp:bus1`	MW	Compensation (Losses)
`n:Pnet:bus1`	MW	External Networks, Active Power
`n:Pflow:bus1`	MW	Power Flow, Active Power
`s:scale`	·	Scale Factor
`s:pini_set`	·	Nominal Active Power

Read after ComMod with GetAttribute. c: calculation parameter, s: signal (state or model variable).

Attribute	Unit	Description
`c:hpi`	rad/s	pini
`c:pini`	MW	loddy_l
`c:lodst_l`	·	Static
`c:loddy_l`	·	Dynamic
`c:kpf`	·	Static Frequency Dependence
`c:kqf`	·	Static Frequency Dependence
`c:t1`	s	Dynamic Load Time Constant
`c:sd0`	MVA	Nominal power of dynamic load
`c:sd00`	MVA	Nominal power of dynamic load
`c:udmax`	p.u.	Upper Voltage Limit
`c:udmin`	p.u.	Lower Voltage Limit
`c:fe`	p.u.	Electrical Frequency
`c:scale`	·	bQ
`c:lodsp_l`	·	Special
`c:tpu`	·	Transient Voltage Dependence
`c:tqu`	s	Transient Voltage Dependence
`c:ssp0`	MVA	Nominal power of special load
`c:ssp00`	MVA	Nominal power of special load
`c:u0`	p.u.	Nominal voltage
`c:i_nln`	·	Internal Flag
`c:kpu0`	·	Volt. Dependence I on P
`c:kqu0`	·	Volt. Dependence I on Q
`c:kpu1`	·	Volt. Dependence II on P
`c:kqu1`	·	Volt. Dependence II on Q
`c:kpu`	·	Volt. Dependence III on P
`c:kqu`	·	Volt. Dependence III on Q
`c:aP`	·	Percent of Volt. Dep. I on P
`c:bP`	·	Percent of Volt. Dep. II on P
`c:aQ`	·	Percent of Volt. Dep. I on Q
`c:bQ`	·	Percent of Volt. Dep. II on Q
`c:motorA`	CalLodwecc1pac,CalLodweccasm	Motor A
`c:motorB`	CalLodwecc1pac,CalLodweccasm	Motor B
`c:motorC`	CalLodwecc1pac,CalLodweccasm	Motor C
`c:motorD`	CalLodwecc1pac,CalLodweccasm	Motor D
`c:Tap`	p.u.	Transformer tap
`c:Rfdr`	p.u.	Feeder R (p.u. of MVA base)
`c:Xfdr`	p.u.	Feeder X (p.u. of MVA base)
`c:Bfdr`	p.u.	Value of the total feeder reactive compensation
`c:Vls`	p.u.	Voltage at substation low-side bus
`c:Vld`	p.u.	Voltage at load end of feeder
`c:Pst`	·	Pst
`c:Qst`	·	Qst
`c:Pel`	·	Pel
`c:Qel`	·	Qel
`c:Fv1`	·	Fv1
`c:qini`	Mvar	Nominal Reactive Power
`c:tpf`	s	Transient Frequency Dependence
`c:tqf`	s	Transient Frequency Dependence
`c:glod`	p.u.	Conductance
`c:gs0`	p.u.	Conductance
`c:bs0`	p.u.	Susceptance
`c:x`	p.u.	Reactance
`c:r`	p.u.	Resistance
`c:slip`	p.u.	Slip
`c:s0pu`	p.u.	Slip at Normal Operation Point
`c:scrpu`	p.u.	Critical Slip
`c:tm00`	p.u.	Ratio of Dynamic Load (Normal Operating Torque)
`c:Tj`	s	Acceleration time constant
`c:i_dyn`	·	i_dyn
`c:xme`	p.u.	Electrical Torque
`c:xmt0`	p.u.	Initial mechanical torque
`c:tm1`	·	Mechanical Torque Exponent
`c:speed0`	p.u.	Initial speed
`c:xmt`	p.u.	Mechanical Torque
`c:ushed`	p.u.	Voltage setting for load shedding
`c:shape`	·	Shape of Load Shedding Probability Function
`c:fshed`	p.u.	Load-Shedding Factor
`c:ureclose`	p.u.	Voltage setting for reclosing
`c:currr`	p.u.	Rotor Current, Real Part
`c:curri`	p.u.	Rotor Current, Imaginary Part
`s:xu`	p.u.	State Variable
`s:Pext`	MW	Active Power Input
`s:Qext`	Mvar	Reactive Power Input
`s:fref`	p.u.	Reference Frequency
`s:xf`	p.u.	State Variable
`s:speed`	p.u.	Speed
`s:xmdm`	p.u.	MDM-Torque
`s:psirr`	p.u.	Rotor Flux, Real Part
`s:psiri`	p.u.	Rotor Flux, Imaginary Part
`s:fshedin`	p.u.	Load-Shedding Factor

ElmLod optimal power flow results

Read after ComOpf with GetAttribute. m: currents, voltages and powers, c: calculation parameter, n: bus result at a terminal.

Attribute	Unit	Description
`m:urnet:bus1`	p.u.	Voltage, Real Part, referred to network
`m:uinet:bus1`	p.u.	Voltage, Imaginary Part, referred to network
`m:u1r:bus1`	p.u.	Positive-Sequence-Voltage, Real Part
`m:u1i:bus1`	p.u.	Positive-Sequence-Voltage, Imaginary Part
`m:u1:bus1`	p.u.	Positive-Sequence-Voltage, Magnitude
`m:U1:bus1`	kV	Line-Ground Positive-Sequence-Voltage, Magnitude
`m:U1l:bus1`	kV	Line-Line Positive-Sequence-Voltage, Magnitude
`m:phiu1:bus1`	deg	Positive-Sequence-Voltage, Angle
`m:irnet:bus1`	p.u.	Current, Real Part, referred to network
`m:iinet:bus1`	p.u.	Current, Imaginary Part, referred to network
`m:inet:bus1`	p.u.	Current, Magnitude, referred to network
`m:I:bus1`	kA	Current, Magnitude
`m:phii:bus1`	deg	Current, Angle
`m:i1r:bus1`	p.u.	Positive-Sequence Current, Real Part
`m:i1i:bus1`	p.u.	Positive-Sequence Current, Imaginary Part
`m:i1:bus1`	p.u.	Positive-Sequence Current, Magnitude
`m:I1:bus1`	kA	Positive-Sequence Current, Magnitude
`m:phii1:bus1`	deg	Positive-Sequence Current, Angle
`m:P:bus1`	MW	Active Power
`m:Q:bus1`	Mvar	Reactive Power
`m:S:bus1`	MVA	Apparent Power
`m:cosphi:bus1`	·	Power Factor
`m:tanphi:bus1`	·	tan(phi)
`m:Psum:bus1`	MW	Total Active Power
`m:Qsum:bus1`	Mvar	Total Reactive Power
`m:Ssum:bus1`	MVA	Total Apparent Power
`m:cosphisum:bus1`	·	Total Power Factor
`m:tanphisum:bus1`	·	Total tan(phi)
`m:i1P:bus1`	p.u.	Positive-Sequence Active Current
`m:i1Q:bus1`	p.u.	Positive-Sequence Reactive Current
`m:I1P:bus1`	kA	Positive-Sequence Active Current
`m:I1Q:bus1`	kA	Positive-Sequence Reactive Current
`m:ur:bus1`	p.u.	Voltage, Real Part
`m:ui:bus1`	p.u.	Voltage, Imaginary Part
`m:u:bus1`	p.u.	Voltage, Magnitude
`m:ir:bus1`	p.u.	Current, Real Part
`m:ii:bus1`	p.u.	Current, Imaginary Part
`m:i:bus1`	p.u.	Current, Magnitude
`m:phiui:bus1`	deg	Angle between Voltage and Current
`m:phiu1i1:bus1`	deg	Angle between Voltage and Current in positive sequence system
`m:Tfct:bus1`	s	Fault Clearing Time
`m:Brkload:bus1`	%	Breaker Loading
`m:Spu:bus1`	MVA/p.u.	Apparent Power per p.u. Voltage
`c:frnom`	Hz	Nominal Frequency
`c:hpi`	rad/s	Nominal angular frequency
`c:pini`	MW	Nominal Active Power
`c:scale0`	·	Initial Scale Factor
`c:s`	·	Complex Power (P+jQ)
`c:u0`	p.u.	Nominal Voltage
`c:kpu0`	·	Volt. Dependence I on P
`c:kqu0`	·	Volt. Dependence I on Q
`c:kpu1`	·	Volt. Dependence II on P
`c:kqu1`	·	Volt. Dependence II on Q
`c:kpu`	·	Volt. Dependence III on P
`c:kqu`	·	Volt. Dependence III on Q
`c:aP`	·	Percent of Volt. Dep. I on P
`c:bP`	·	Percent of Volt. Dep. II on P
`c:aQ`	·	Percent of Volt. Dep. I on Q
`c:bQ`	·	Percent of Volt. Dep. II on Q
`c:Qnom`	Mvar	Nominal Reactive Power
`c:ncust`	·	Number of Connected Customers
`c:i_rem`	·	Remote Control
`c:zonescale`	·	Zone Scale Factor
`c:iRefElement`	·	Reference Element
`c:Pmism`	MW	Active Power Mismatch
`c:Ploss`	MW	Losses (total)
`c:Qloss`	Mvar	Reactive-Losses (total)
`c:Plossld`	MW	Losses (load)
`c:Qlossld`	Mvar	Reactive-Losses (load)
`c:Plossnld`	MW	Losses (no load)
`c:Qlossnld`	Mvar	Reactive-Losses (no load)
`c:qini`	Mvar	Nominal Reactive Power
`c:Pnom`	MW	Nominal Active Power
`c:Ppeak`	MW	Peak Active Power
`c:Qpeak`	Mvar	Peak Reactive Power
`c:p`	MW	Power
`c:gs0`	p.u.	Conductance
`c:bs0`	p.u.	Susceptance
`c:x`	p.u.	Reactance
`c:r`	p.u.	Resistance
`c:slip`	p.u.	Slip
`n:ur:bus1`	p.u.	Voltage, Real Part
`n:ui:bus1`	p.u.	Voltage, Imaginary Part
`n:u:bus1`	p.u.	Voltage, Magnitude
`n:upc:bus1`	%	Voltage, Magnitude
`n:du:bus1`	%	Voltage Deviation
`n:U:bus1`	kV	Line-Ground Voltage, Magnitude
`n:phiu:bus1`	deg	Voltage, Angle
`n:phiurel:bus1`	deg	Voltage, Relative Angle
`n:Ul:bus1`	kV	Line-Line Voltage, Magnitude
`n:u1:bus1`	p.u.	Voltage, Magnitude
`n:u1pc:bus1`	%	Voltage, Magnitude
`n:u1r:bus1`	p.u.	Positive-Sequence Voltage, Real Part
`n:u1i:bus1`	p.u.	Positive-Sequence Voltage, Imaginary Part
`n:Pgen:bus1`	MW	Generation, Active Power
`n:Qgen:bus1`	Mvar	Generation, Reactive Power
`n:Pmot:bus1`	MW	Motor Load, Active Power
`n:Qmot:bus1`	Mvar	Motor Load, Reactive Power
`n:Pload:bus1`	MW	General Load, Active Power
`n:Qload:bus1`	Mvar	General Load, Reactive Power
`n:Pcomp:bus1`	MW	Compensation (Losses)
`n:Qcomp:bus1`	Mvar	Compensation
`n:Pnet:bus1`	MW	External Networks, Active Power
`n:Qnet:bus1`	Mvar	External Networks, Reactive Power
`n:Pflow:bus1`	MW	Power Flow, Active Power
`n:Qflow:bus1`	Mvar	Power Flow, Reactive Power
`n:Pout:bus1`	MW	Outgoing Flow, Active Power
`n:Qout:bus1`	Mvar	Outgoing Power, Reactive Power
`n:Sout:bus1`	MVA	Outgoing Power, Apparent Power
`n:cosphiout:bus1`	·	Outgoing Power, Power Factor
`n:Pbalance:bus1`	MW	Active Power Balance (=0)
`n:Qbalance:bus1`	Mvar	Reactive Power Balance (=0)
`n:LossPdown:bus1`	MW	Losses, downstream
`n:LossQdown:bus1`	Mvar	Losses, downstream (Reactive Power)
`n:LossPdownload:bus1`	MW	Load losses, downstream
`n:LossQdownload:bus1`	Mvar	Load losses, downstream
`n:LossPdownnoload:bus1`	MW	No load losses, downstream
`n:LossQdownnoload:bus1`	Mvar	No load losses, downstream
`n:du_feed:bus1`	%	Difference from voltage at start of feeder

ElmLod basic data

b: values are worked out from the input data. Read them; they are not set.

Attribute	Unit	Description
`b:loc_name`	·	Name

← ElmFilter Harmonic Filter · ElmLodlv Low-Voltage Load →